LM R e Thin Film Resistor Network. 0 05% Matching and 5 ppm This datasheet has been download from: Datasheets for electronics components. On all operational amplifier data sheets, the specifications listed on the deep in the data sheet. .. , LM and LT with improved price/performance. LM Datasheet: LM Precision Operational Amplifier, LM PDF Download National ->Texas Instruments, LM Datasheet PDF, Pinouts, Data Sheet.
|Published (Last):||27 August 2017|
|PDF File Size:||15.39 Mb|
|ePub File Size:||20.89 Mb|
|Price:||Free* [*Free Regsitration Required]|
LM607 PDF Datasheet浏览和下载
There is no guarantee that the Specified Temperatures are exactly at the minimum or maximum deviation. Ceramic capacitors may seem to do the job, but are not recommended for production use, as the high-K ceramics cannot be llm607 for low leakage, and may exhibit piezo-electric effects, converting vibration or mechanical stress into excessive electrical noise.
The capacitor used should be a low-leakage type. The LM is suitable for limited-temperature operation. The trim scheme is such that individual resistors are cut open rather than being trimmed partially cutto avoid resistor drift caused by electromigration in the trimmed area. In Sinking mode, connect 0.
LM (NSC) PDF技术资料下载 LM 供应信息 IC Datasheet 数据表 (1/41 页)
This datasheet has been downloaded from: These pins would not be damaged by a short to ground, or by Electrostatic Discharges; however, keep them away from large transients or AC signals, as stray capacitance could couple noises into the output. Pin numbers for H, M or N packages. These limits are not to be used to calculate outgoing quality levels.
However, avoid overloads at high ambient temperatures, as a prolonged short-circuit may cause the junction temperature to exceed the Absolute Maximum Temperature. The curves showing the Noise vs. Capacitance in the Typical Performance Characteristics section show graphically that a modest capacitance of 0.
In some applications it may be advantageous to pre-load the output to either Vin or to ground, to avoid this crossover point.
LM – LM part cross-reference datasheet –
National Semiconductor Europe Fax: Thermal regulation is defined as the datzsheet in the output voltage at a time T after a step change of power dissipation of mW. They are based on a buried zener reference as pioneered in the LM references, but do not require any heater, as they rely on special temperature-compensation techniques Patent Pending.
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. If the output is pulled to a positive voltage such as a 15 or a 20V, the output current will be limited, but overheating may occur.
The output has a class-B stage, so if the load current changes from sourcing to sinking, an output transient will occur. The output can sink current as well as l6m07 it, but the output impedance is datsheet better for sourcing current. The LM datashet a Class B output, and will exhibit transients at the crossover point. A trim pin is available which permits fine-trimming of Vout, and also permits filtering to greatly decrease the output noise by adding a small capacitor 0. The LM also provides excellent stability vs.
Unless otherwise noted, these conditions apply: Consult factory for availability of devices with tighter Accuracy and Tempco Datashdet. Life support devices or systems are devices or systems which, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
Its long-term stability is typically 3 to 10 ppm per hours when held near Tmax, and slightly better when operated at room temperature. The LM is recommended for applications where the highest stability and lowest lm6077 is required over the full military temperature range.
To avoid this transient, it may be advisable to preload the output with a few milliamperes of load to ground.
Documents Flashcards Grammar checker. The devices have a LM see curve above: For example, if the output were trimmed up to Tsimshatsui, Kowloon Hong Kong Tel: This point occurs when the device is required to sink approximately 1. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
Consult factory for availability of devices with Guaranteed Long-term Stability. Contact the factory for availability of devices with proven long-term stability.