HUAWEI RTN 950 MANUAL PDF

OptiX RTN Radio Transmission System. VRC Commissioning and Configuration Guide (Web LCT). Issue, Date, HUAWEI. Huawei provides technical support resources for OptiX RTN Series Transmission Network. Access product manuals, HedEx documents, and visio stencils. Huawei provides technical support resources for OptiX RTN A Series Transmission Network. Access product manuals, HedEx documents, and visio stencils.

Author: Netaur Kajijas
Country: Kenya
Language: English (Spanish)
Genre: Politics
Published (Last): 22 September 2005
Pages: 292
PDF File Size: 17.5 Mb
ePub File Size: 7.89 Mb
ISBN: 388-2-19450-207-4
Downloads: 40228
Price: Free* [*Free Regsitration Required]
Uploader: Grojas

On both ends of a radio link, power on the NEs. Step 5 When you need to synchronize the NE time with the NMS time, set the time synchronization mode and the related parameters. The CPU has the ability to fetch, decode, and execute instructions and to transfer information to and from other resources over the computer’s main data-transfer path, the bus. The signal peak of the first side lobe at point 6 and the signal peak of the first side lobe at point 7 appear as one signal peak.

RTN 950 V100R003C03 Configuration Guide 04(WebLCT)

Two seconds later, the login window is displayed. ATPC Upper – The greater the bandwidth, the faster the data transfer rate. Step 4 Disable the E1 priority function and AM function on the radio link between two sites. NOTE If basic information about the opposite NEs in a certain microwave direction is not displayed, check the configurations in that microwave direction.

Reconfigure the E1 services that were deleted in Step 3. In this service, the diagrams are forwarded following the sequence of the time they reach.

  ALIEN ENCOUNTERS CHUCK MISSLER MARK EASTMAN PDF

Configure the upper-layer NTP server.

Antenna movement across the main lobe results in a rapid rise and fall in the signal level. Documents The following document should be available before commissioning the equipment: Click Options to change the VC timeslot numbering policy used by the cross- huawi. Step 2 Install or remove the IF cable. Otherwise, relog in to the system according to the prompt message of the system.

RTN 950 V100R005C00 Commissioning Guide 02

Set parameters as follows: Step 5 Refer to 5. A high received optical power damages the optical interface. That is, services are transmitted and received in a different tunnel respectively.

Do not hold the handles of the modules installed in the chassis, such as the power modules, fan modules, and boards. In normal cases, mznual an un-terminated optical fiber or a damaged optical fiber without eye protection at a distance greater than mm does not cause eye injury.

Set Huawwi and Subnet Mask as required. If multiple transmit antennas are installed on a tower or backstay, keep away from the transmit directions of the antennas when you install or maintain an antenna locally.

Slightly adjust the elevation and azimuth at point 2 as shown in Figure until VBNC reaches the peak within the tracked range. Instructions Regarding Fiber Handling Read and abide by the following instructions before handling fibers: Therefore, the FMs of the working and protection boards are reported at the same time. In Current Status, the service switching mode is displayed. Hold priority The priority of the tunnel with respect to holding resources, ranging from 0 indicates the highest priority to 7.

Once a signal is detected, very small alignment adjustments are required to locate the main lobe. It is prohibited huaqei you use alcohol and formalin. In this case, an NE can be accessed by using the U, and the networkwide service data can be configured.

  ATMEGA2560 DATASHEET FILETYPE PDF

OptiX RTN Radio Transmission System Commissioning Guide (U | Jairo Bejarano –

Frequency Conference Call – l This parameter indicates the telephone number of the network-wide orderwire conference call. Select 2-Frequency and press Enter.

Huwei features high speed and low error rate. Use the optical distribution frame ODF to connect an attenuator to a level optical interface. Click the General tab. Prerequisite l Hardware installation has been completed and has passed the installation check. Then, right-click the selected unit. It indicates that the bypass tunnel should be able to protect the downstream node that is involved in the working tunnel and adjacent to the PLR. The Attribute dialog box is displayed.

Engineers also need to adjust the feed booms of the antennas so that the cross-polarization discrimination XPD meets the specified requirements. This parameter must be larger than 0.

Safety Instructions Regarding Lasers To avoid laser radiation, obey the following instructions: Step 8 Check service availability after the switching. Thunderstorm The requirements apply only to wireless base stations or devices with antennas and feeders.

With the highest priority, the operation is performed no matter whether the current status of huawe protection tunnel is normal.