CONFIGURATION OSPF ROUTEUR CISCO PDF

This of course leads to more complexity in the configuration and troubleshooting of OSPF networks. Administrators that are used to the. This document shows sample configurations for Open Shortest Path First (OSPF) authentication which allows the flexibility to authenticate. router-id-ospf. Command Default. If this command is not configured, OSPF chooses an IPv4 address as the router ID from one of its interfaces.

Author: Nikorr Duran
Country: Iran
Language: English (Spanish)
Genre: Environment
Published (Last): 22 June 2016
Pages: 245
PDF File Size: 14.26 Mb
ePub File Size: 14.99 Mb
ISBN: 612-5-54747-792-1
Downloads: 56236
Price: Free* [*Free Regsitration Required]
Uploader: Vijar

Configuring The OSPF Router-ID | Free CCNA Workbook

Therefore, both should act in the same way, or am I wrong? BGP table version is 9local router ID is 3. Process 2, Nbr 4. First bring 3 routers into your topology R1, R2, R3 position them as below.

R3 hostname R3 int lo0 ip add 3. The initial config lists setting it with a R1 sh bgp vpnv4 unicast all summary.

MPLS Tutorial – MPLS Configuration Step by Step

R6 sh ip route 4. I am Oussema from Tunisia and I have found this tutorial very useful for me. I would be so grateful.

The Router-ID uniquely identifies a router in an autonomous system, no two routers in an OSPF autonomous system can have the same router-id. Shawn, There was a delay in writing this post but it is complete now. R4 sh ip route.

What is difference between ABR and ASBR in OSPF network? – Network Bulls

If the output does not display the intended configuration, repeat the instructions in this example to correct the configuration. Establish a console session with devices R1, R2, R3, R4, R5 and SW1 than load the initial configurations provided below by copying the config from the textbox and pasting it into the respected routers console. These will be the customer sites connected to R1 and R3.

  BS EN 10248-1 PDF

Here you can see Routing Table: Currently working for Softcat plc. Tracing the route to 6. Now at this point we have R4 peering to R1 but in the global routing table of R1 which is not what we want. If a router-id is not configured manually in the OSPF routing process the router will automatically configure a router-id determined from the highest IP address of a logical interface loopback interface or the highest IP address of an active interface.

We now have this setup. R1 router bgp 1 neighbor 3.

Junos OS selects a router identifier according to the following set of rules:. To quickly configure an OSPF router identifier, copy the following commands, paste them into a text file, remove any line breaks, change any details necessary to match your network configuration, copy and paste the commands into the CLI at the [edit] hierarchy level, and then enter commit from configuration mode.

Configuration du routage ospf – routeur Cisco

Gateway of last resort is not set. Packet sent with a source address of cksco. This command is executed in OSPF router configuration mode to statically configure a router id on a specific neighbor.

  INFOCUS IN5122 PDF

Configure the device interfaces. R3 sh ip bgp vpnv4 vrf RED. R2 sh mpls interface. It will use the local site addressing of Comments Hi Roger, Very nice and self explanatory tutorial. Remember we have a VRF configured on this router so this command will show configuraton in the global routing table the MPLS Core and it will not show the Thank You Michael, I am glad you enjoyed the tutorial, I will be putting up a video of the entire process soon and then as promised the second video, but I have just changed jobs so it might be a few weeks.

R6 sh ip route. I have a question. R1 sh ip route Codes: We are oospf to address the routers and configure ospf to ensure loopback to loopback connectivity between R1 and R3.

Ateet, I have updated the tutorial and it is now complete, please review the last steps again and let routwur know if you get any issues.

R1 sh ip route vrf red. R1 sh bgp vpnv4 unicast all summary BGP router identifier 1.