ASTM E29 PDF

within 72 hours in accordance with ASTM E “Standard Test Method for specification compliance in ASTM E “Standard Practice for Using. industry references The American Society for Testing Materials (ASTM) Standard. E, “Practice for Using Significant Digits in Test Data to Determine. ASME中国制造-ASTM E (原文)_化学_自然科学_专业资料。Designation: E29? 13 An American National Standard Standard Practice for.

Author: Shakajin Faebei
Country: Guadeloupe
Language: English (Spanish)
Genre: Literature
Published (Last): 12 November 2005
Pages: 135
PDF File Size: 20.35 Mb
ePub File Size: 10.70 Mb
ISBN: 149-6-37595-781-1
Downloads: 77401
Price: Free* [*Free Regsitration Required]
Uploader: Bragrel

ASTM E29 – 13

That is, the rounding unit for the speci? Permission rights to photocopy the standard may also be secured from the ASTM website www. Dimensional quantities in the practice are presented only as illustrations of calculation methods.

The rounded value should then be compared with the speci? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Awtm. Under these conditions, the speci?

A test result is calculated as 1. Last previous edition approved in as E29 — Its aim is to outline methods which should aid in clarifying the intended meaning of speci?

Rounding this value to the nearest whole number gives a value of 4, based on the information in 6. The examples are not binding on products or test methods treated. In such cases, the following procedure can be used for rounding to any interval: Table 1 gives examples of applying this rounding procedure.

  JEDENJE BOGOVA PDF

Originally approved in Write down the standard deviation. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

The standard deviation of the test method is estimated to be, 0. Tensile Requirements Tensile strength, psi Yield point, min, psi Elongation in 2 in.

Two commonly accepted methods of rounding data, identified as the absolute method and the rounding method are described. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

The examples are not binding on products or test methods treated. NOTE 2—Using a calculation subroutine that has been programmed to perform the rounding procedure described in 6.

Excel: Round towards Even Per ASTM-E29 – Excel Articles

The choice of method depends upon the current practice of the particular branch of industry xstm technology concerned, and should therefore be speci?

This abstract is a brief summary of the referenced standard. The conversion constant, For example, the numbers The rounding interval for test results should not be greater than 0. For purposes of determining conformance with these speci?

Multiplying 4 by 0. Thus, any deviation, however small, outside the speci? The following guidelines are intended to preserve the data for statistical summaries. If you aastm that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

ASME中国制造-ASTM E (原文)_百度文库

ICS Number Code Referenced Documents purchase separately The documents listed below are referenced within the subject standard e299 are not provided as part of the standard. Current edition approved Aug. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

  AMBIGRAMS REVEALED PDF

When 12 is divided by 2, the resulting number, 6is the rounded value aztm 6 For certain purposes, such as where calculations involve differences of measurements close r29 magnitude, and for some statistical calculations, such as paired t-tests, autocorrelations, and nonparametric tests, reporting data to a greater number of signi?

Historical Version s – view previous versions of standard Work Item s – proposed revisions of this standard Translated Version s: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Reporting s to within 0. The suggested rule would report x?

Zeros trailing the last nonzero digit for numbers represented with a decimal point are signi? The average and standard deviation, unrounded, are x? Historical Version s – view previous versions of standard.

The guidelines for retaining significant figures in calculation and reporting of test aztm are presented in details. For example, the number 0.