This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D on Plastics. ASTM D is similar to ISO and describes a procedure for determining the compressive properties of rigid cellular materials. Similar to ISO , ASTM D is a testing standard designed to measure the compressive properties of rigid cellular plastics (i.e. foam).
|Country:||Saint Kitts and Nevis|
|Published (Last):||24 October 2016|
|PDF File Size:||9.46 Mb|
|ePub File Size:||14.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM D – 16 Standard Test Method for Compressive Properties of Rigid Cellular Plastics
Due to the very large number of tests offered, descriptions of those most commonly requested have been gathered into the following groups: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Software for Series Systems. The brochure addresses the most prominent and widely-used standards in the materials testing industry for plastics. These test specimens are carefully prepared so the faces are parallel to each other and perpendicular to the sides. Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill.
The preload function reduces the amount of operator interaction, saving time and improving accuracy.
The values in parentheses are for information only. Suitable systems for this application include Series and Series electromechanical testing machines equipped with compression platens. The self-aligning nature of this fixture will maximize the contact area between the platen and the specimen.
ASTM D1621-16 Compressive Properties of Rigid Cellular Plastics
Historical Version s – view previous versions of standard. Concrete, Asphalt and Rock. Touchstone Research Laboratory, Ltd. ASTM Astmm Testing is the compressive strength of a cellular material determined by applying load to a test specimen with a square or circular cross section.
Discover simpler and smarter testing with features such as pre-loaded test methods, QuickTest in seconds, enhanced data exporting: After testing and analysis, compressive strength, modulus and deformation at maximum load are reported. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as ashm of the standard. Email addresses must contain the symbol. Plastics Testing Solutions Brochure The Plastics Testing Solutions brochure is a page, applications-focused, and standards-based brochure.
It is important to review ASTM D in order to fully understand the test setup, procedure, and results requirements.
Glossary of Materials Testing Terms. Link to Active This link will always route to the current Active version of the standard.
ASTM D1621 – Compression Testing of Rigid Cellular Plastics
They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator. The test specimens are centered between two compression platens photo below left and load is applied at a constant crosshead or actuator rate.
Onsite Training At Your Facility. If there are no material specifications, then the default conditions apply.
ASTM D Compressive Properties Rigid Cellular Plastics – Instron
Bluehill Universal Brochure Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive aztm experience.
To reduce the possible effects from off-center loading, it is preferred to place the swivel seat in the base. Email addresses can only contain letters, numbers and the following special characters: Description Literature Contact Us ASTM D specifies the test conditions for determining the compressive properties of rigid cellular materials, particularly expanded plastics.
Bluehill LE for Basic Testing. The challenges of testing to this asrm are: The data obtained from the compression tests provide a standard method of obtaining data for research and development and quality control. The x series LVDTs can mount directly on the series compression platens.
Select from list below: Instron offers linear variable displacement transducers LVDTs for measurement directly from the platens. Any test specimen preparation, conditioning, dimensions, or testing parameters, or a combination thereof, covered in the materials specification shall take precedence over those mentioned in this test method.
The preload function ashm Bluehill Universal software automatically moves the upper compression platen down to precisely touch f1621 specimen at a pre-defined load. Next Checking to see if you are a returning visitor….
Subscribe to Instron News!